行業資訊

水穩攤鋪施工過程需要注意的事項

來源：http://www.shyy66.com/ 日期：2023-06-16

混合料的拌和

Mixing of mixtures

濟南水穩砼廠家提醒您，在開始拌合前，拌合場的備料應滿足3~5天的攤鋪用料。每天開始攤鋪前，應檢查場內各處集料的含水量，計算當日的配合比，外加水與天然含水量的總和要比佳含水量略高1個百分點。

Jinan water stabilized concrete manufacturer reminds you that before starting mixing, the material preparation at the mixing plant should meet the paving requirements of 3-5 days. Before starting paving every day, the moisture content of the aggregates in various parts of the site should be checked, and the mix ratio for that day should be calculated. The total amount of added water and natural moisture content should be slightly higher than the optimal moisture content by 1 percentage point.

每天開始攪拌之后，出料要檢查是否符合設計配合比，進行正式生產之后，每1~2小時檢查一次拌合情況，抽檢其配合比、含水量是否變化。

After starting mixing every day, the discharge should be checked for compliance with the designed mix ratio. After formal production, the mixing condition should be checked every 1-2 hours, and the mix ratio and water content should be randomly checked for any changes.

高溫作業時，早晚與中午的含水量要有區別，要按溫度變化及時調整。拌合機出料不允許采取自由落地、裝載機裝料運輸?shù)霓k法，采用由漏斗出料直接裝料運輸。裝車時車輛應前后移動，分三次裝料，避免混合料離析。

During high-temperature operations, there should be a difference in water content between morning and evening and noon, and adjustments should be made in a timely manner according to temperature changes. The method of free landing and loading and transportation by loader is not allowed for the discharge of the mixer, and direct loading and transportation by funnel discharge is adopted. When loading, the vehicle should move forward and backward, loading in three stages to avoid segregation of the mixture.

混合料的攤鋪

Spreading of mixture

攤鋪前應將下層適當灑水潤濕。混合料運至施工現場后，采用攤鋪機攤鋪的方法按照掛設的高程控制線進行攤鋪。掌握好松鋪厚度與壓實后厚度的關系，進而嚴格控制好水穩層的壓實厚度和高程，確保壓實厚度滿足設計要求。好是配備基于北斗定位的智能攤鋪系統，可以大大提高工程質量以及降低人工成本。

Before paving, the lower layer should be properly moistened with water. After the mixture is transported to the construction site, it is spread using a paver according to the elevation control line set up. Master the relationship between the loose paving thickness and the compacted thickness, and strictly control the compacted thickness and elevation of the water stable layer to ensure that the compacted thickness meets the design requirements. The good thing is to equip an intelligent paving system based on Beidou positioning, which can greatly improve project quality and reduce labor costs.
濟南水穩砼

混合料的碾壓

Rolling of mixture

攤鋪后壓路機應及時進行碾壓。一次碾壓長度一般為50m左右。穩壓要充分，振壓不起浪花、不推移。壓實時，可以先穩定（遍數適中，壓實度達到85%）→開始輕振動碾壓→再重振動碾壓→后穩壓，壓至無輪跡為止。碾壓過程中，可用灌砂法檢測壓實度，不合格時，重復再壓（注意檢測壓實時間）。直至碾壓壓實度合格為止。

After paving, the roller should be rolled in a timely manner. The length of one compaction is generally about 50m. The voltage stabilization should be sufficient, and the vibration pressure should not cause waves or movement. When compacting, it is possible to first stabilize (with a moderate number of passes and a compaction degree of 85%), then start light vibration compaction, then heavy vibration compaction, and then stabilize until there are no wheel marks. During the compaction process, the sand filling method can be used to test the compaction degree. If it is not qualified, repeat the compaction (pay attention to the compaction time). Until the compaction degree is qualified.

水穩攤鋪施工過程需要注意的事項就講解到這里了，希望能夠給您好的幫助，更多事項就來我們網站http://www.shyy66.com咨詢吧！

That's all we need to pay attention to during the construction process of water stabilized paving. We hope to provide you with good help. For more details, please visit our website http://www.shyy66.com Consult!

上一條：壓路機在路面壓實過程中的六大技巧

下一條：關于瀝青砼的主要內容介紹